Discovering Plumbing Basics is Important For Installing a Bathtub
Discovering Plumbing Basics is Important For Installing a Bathtub
Blog Article
This great article which follows relating to Tools You Need to Install a New Bathtub is totally entertaining. Read on and draw your own final thoughts.
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub and set in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Instead of hiring a professional to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This short article will certainly help you set up a new tub in your bathroom if you have already acquired a new tub and don't need to transform the arrangement of your previous water pipelines.
Your devices and also material checklist should consist of the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to stop strain on the bathtub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be rather bothersome because of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water as well as examine all joints and new pipework for leakages and tighten them if needed. Load the tub as well as also check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub ought to wait up until the tub has been utilized at the very least when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the tap in place with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and the tiling, leading to problems with dampness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are sold in tubes and cartridges, as well as can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the motion experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not take into consideration this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads on How to Install a Bathtub Yourself, I assumed sharing that information was a good idea. I beg you take the opportunity to distribute this article if you appreciated it. Thank you so much for going through it.
Overflow? Seek assistance. Report this page